Symptoms of P0568
- Unstable, high, or low idle, or stalling.
- Erratic speedometer, cruise-control, or shift behaviour.
- Check-engine light with a hesitation or surge.
Common causes of P0568
- A dirty throttle body, idle-control valve, or throttle-position sensor.
- A failing vehicle-speed or wheel-speed sensor, or its wiring.
- Vacuum leaks or a related sensor forcing the idle/speed strategy.
Useful checks before replacing parts
- Compare set switch state, resume and coast inputs, brake switch data, vehicle speed, cruise enable status, and freeze-frame conditions.
- Inspect steering wheel switch contacts, clockspring wiring, column connectors, shared resistor circuits, corrosion, and liquid intrusion.
- Press the set control while monitoring live data to verify the request changes correctly and is not stuck or missing.
How serious is P0568, and can you keep driving?
- Urgency
- Moderate, and a safety matter if it stalls
- Safe to drive?
- Only if the idle is stable and it has not stalled on you.
Faults in this family show up as unstable idle, stalling at junctions, or a throttle that does not respond the way you asked. A car that cuts out as you pull into traffic is a safety problem, not an inconvenience, and many vehicles will drop to a reduced-power limp mode to protect themselves. If it has stalled once in traffic, stop driving it.
Clearing P0568, and making it stay gone
Clearing P0568 with a scan tool switches the lamp off; it does not fix anything, and it throws away the freeze-frame snapshot the car saved when the fault set. That snapshot is the most useful diagnostic evidence you have, because it records the load, RPM and temperature at the moment the test failed. Read it before you erase it.
Left alone, the lamp goes out on its own once the monitor that failed runs and passes on three consecutive driving cycles. The code stays in history after that, which is how a workshop can still see it. Disconnecting the battery is not a shortcut — it clears the stored codes and every learned fuel-trim value with them, so the car relearns from scratch and the underlying fault simply sets the code again.
On vehicles from roughly 2010 onward there is also a permanent DTC, which no scan tool can erase at all. It clears only when the monitor genuinely passes. That is deliberate: it stops a code being wiped in the car park outside an emissions test.
What P0568 costs to put right
There is no honest single figure for P0568, and any page that gives you one is guessing. The code names a circuit or a failed monitor, not a part — the same code can be a chafed wire, a connector full of water, or the component itself, and those are three very different bills.
The number worth budgeting for is diagnostic time. An hour of it is almost always cheaper than the second part you buy after the first one does not fix it, and parts fitted on a guess are rarely refundable once installed. If you are getting a quote, ask what the diagnosis found rather than what is being replaced — a speed / idle fault traced to a specific cause is a repair, and a list of parts is a hopeful shopping list.
Questions people ask about P0568
What does P0568 mean?
P0568 indicates a cruise control set signal malfunction. The controller is not receiving a valid set request from the cruise switch input circuit.
Can I drive with P0568?
Only if the idle is stable and it has not stalled on you. Faults in this family show up as unstable idle, stalling at junctions, or a throttle that does not respond the way you asked. A car that cuts out as you pull into traffic is a safety problem, not an inconvenience, and many vehicles will drop to a reduced-power limp mode to protect themselves. If it has stalled once in traffic, stop driving it.
What causes P0568?
The usual candidates are a dirty throttle body, idle-control valve, or throttle-position sensor; a failing vehicle-speed or wheel-speed sensor, or its wiring; vacuum leaks or a related sensor forcing the idle/speed strategy. The code tells you which test failed, not which of those did it — that is what the checks on this page are for.
Will P0568 clear itself?
Left alone, the lamp goes out on its own once the monitor that failed runs and passes on three consecutive driving cycles. The code stays in history after that, which is how a workshop can still see it. Disconnecting the battery is not a shortcut — it clears the stored codes and every learned fuel-trim value with them, so the car relearns from scratch and the underlying fault simply sets the code again.
Does P0568 mean I need to replace a part?
Do not diagnose speed control output components before confirming the set signal reaches the controller.
How much does it cost to fix P0568?
There is no honest single figure for P0568, and any page that gives you one is guessing. The code names a circuit or a failed monitor, not a part — the same code can be a chafed wire, a connector full of water, or the component itself, and those are three very different bills.
Related OBD-II codes
These nearby speed / idle entries can help compare wording and pin down the fault area.