Symptoms of P0848
- Harsh, delayed, or slipping shifts, or being stuck in one gear.
- Check-engine light, sometimes with limp-home mode.
- Flaring RPM or a shudder under load.
Common causes of P0848
- Low or degraded transmission fluid.
- A failing speed sensor, shift solenoid, or pressure-control circuit.
- Wiring, connector, or internal hydraulic/mechanical faults.
Useful checks before replacing parts
- Check for short-to-voltage, open ground, connector damage, internal harness faults, or pressure sensor B stuck high.
- Compare pressure data with commanded pressure, gear state, fluid temperature, and shift feel.
- Review pressure-control solenoid and line-pressure codes that may explain actual high pressure.
How serious is P0848, and can you keep driving?
- Urgency
- High
- Safe to drive?
- If it is slipping, flaring, or shifting harshly — recover it, do not drive it.
Transmission codes are the ones worth taking seriously on the day. Slip and harsh engagement generate heat and debris, and both of those damage the clutches and valve body further every mile you add. Many vehicles will fall back to a limp mode that holds a single gear to protect the unit; that is the transmission asking to be trailered, not a mode to commute in. Check the fluid level and condition before anything else — it is free, and it is a genuinely common root cause.
Clearing P0848, and making it stay gone
Clearing P0848 with a scan tool switches the lamp off; it does not fix anything, and it throws away the freeze-frame snapshot the car saved when the fault set. That snapshot is the most useful diagnostic evidence you have, because it records the load, RPM and temperature at the moment the test failed. Read it before you erase it.
Left alone, the lamp goes out on its own once the monitor that failed runs and passes on three consecutive driving cycles. The code stays in history after that, which is how a workshop can still see it. Disconnecting the battery is not a shortcut — it clears the stored codes and every learned fuel-trim value with them, so the car relearns from scratch and the underlying fault simply sets the code again.
On vehicles from roughly 2010 onward there is also a permanent DTC, which no scan tool can erase at all. It clears only when the monitor genuinely passes. That is deliberate: it stops a code being wiped in the car park outside an emissions test.
What P0848 costs to put right
There is no honest single figure for P0848, and any page that gives you one is guessing. The code names a circuit or a failed monitor, not a part — the same code can be a chafed wire, a connector full of water, or the component itself, and those are three very different bills.
The number worth budgeting for is diagnostic time. An hour of it is almost always cheaper than the second part you buy after the first one does not fix it, and parts fitted on a guess are rarely refundable once installed. If you are getting a quote, ask what the diagnosis found rather than what is being replaced — a transmission fault traced to a specific cause is a repair, and a list of parts is a hopeful shopping list.
Questions people ask about P0848
What does P0848 mean?
P0848 indicates a high input from transmission fluid pressure sensor or switch B. The pressure feedback signal is higher than expected.
Can I drive with P0848?
If it is slipping, flaring, or shifting harshly — recover it, do not drive it. Transmission codes are the ones worth taking seriously on the day. Slip and harsh engagement generate heat and debris, and both of those damage the clutches and valve body further every mile you add. Many vehicles will fall back to a limp mode that holds a single gear to protect the unit; that is the transmission asking to be trailered, not a mode to commute in. Check the fluid level and condition before anything else — it is free, and it is a genuinely common root cause.
What causes P0848?
The usual candidates are low or degraded transmission fluid; a failing speed sensor, shift solenoid, or pressure-control circuit; wiring, connector, or internal hydraulic/mechanical faults. The code tells you which test failed, not which of those did it — that is what the checks on this page are for.
Will P0848 clear itself?
Left alone, the lamp goes out on its own once the monitor that failed runs and passes on three consecutive driving cycles. The code stays in history after that, which is how a workshop can still see it. Disconnecting the battery is not a shortcut — it clears the stored codes and every learned fuel-trim value with them, so the car relearns from scratch and the underlying fault simply sets the code again.
Does P0848 mean I need to replace a part?
Do not condemn hydraulic parts before checking pressure sensor B wiring and whether pressure is actually high.
How much does it cost to fix P0848?
There is no honest single figure for P0848, and any page that gives you one is guessing. The code names a circuit or a failed monitor, not a part — the same code can be a chafed wire, a connector full of water, or the component itself, and those are three very different bills.
Related OBD-II codes
These nearby transmission entries can help compare wording and pin down the fault area.