Symptoms of P0341
- Rough idle, shaking, or a stumble under acceleration.
- A flashing check-engine light during an active misfire.
- Power loss and higher fuel consumption.
Common causes of P0341
- Worn spark plugs, ignition coils, or plug wires.
- Fuel-delivery problems — injectors, pressure, or a lean/rich mixture.
- Vacuum leaks, low compression, or a mechanical fault in that cylinder.
Useful checks before replacing parts
- Compare camshaft and crankshaft signals, synchronization data, and freeze-frame conditions from the fault event.
- Inspect sensor connector fit, wiring, mounting, cam trigger condition, and recent timing or cylinder-head service.
- Check for timing-chain stretch, phaser faults, or correlation codes that can make the cam signal appear out of range.
How serious is P0341, and can you keep driving?
- Urgency
- High when the lamp is flashing
- Safe to drive?
- A flashing check-engine light means stop — a steady one means drive gently and get it looked at.
This is the one code family where the lamp itself tells you the urgency. A steady light means the misfire was detected and logged. A flashing light means it is happening right now and is severe enough to be dumping raw fuel into the catalytic converter, which can overheat and be destroyed in minutes rather than months. Pull over, switch off, and get the car recovered rather than driving it on. A converter costs many times what a coil or a plug does.
Clearing P0341, and making it stay gone
Clearing P0341 with a scan tool switches the lamp off; it does not fix anything, and it throws away the freeze-frame snapshot the car saved when the fault set. That snapshot is the most useful diagnostic evidence you have, because it records the load, RPM and temperature at the moment the test failed. Read it before you erase it.
Left alone, the lamp goes out on its own once the monitor that failed runs and passes on three consecutive driving cycles. The code stays in history after that, which is how a workshop can still see it. Disconnecting the battery is not a shortcut — it clears the stored codes and every learned fuel-trim value with them, so the car relearns from scratch and the underlying fault simply sets the code again.
On vehicles from roughly 2010 onward there is also a permanent DTC, which no scan tool can erase at all. It clears only when the monitor genuinely passes. That is deliberate: it stops a code being wiped in the car park outside an emissions test.
What P0341 costs to put right
There is no honest single figure for P0341, and any page that gives you one is guessing. The code names a circuit or a failed monitor, not a part — the same code can be a chafed wire, a connector full of water, or the component itself, and those are three very different bills.
The number worth budgeting for is diagnostic time. An hour of it is almost always cheaper than the second part you buy after the first one does not fix it, and parts fitted on a guess are rarely refundable once installed. If you are getting a quote, ask what the diagnosis found rather than what is being replaced — a ignition / misfire fault traced to a specific cause is a repair, and a list of parts is a hopeful shopping list.
Questions people ask about P0341
What does P0341 mean?
P0341 points to a range or performance issue in camshaft position sensor A on bank 1 or a single-sensor setup. The signal exists but does not match expected timing behavior.
Can I drive with P0341?
A flashing check-engine light means stop — a steady one means drive gently and get it looked at. This is the one code family where the lamp itself tells you the urgency. A steady light means the misfire was detected and logged. A flashing light means it is happening right now and is severe enough to be dumping raw fuel into the catalytic converter, which can overheat and be destroyed in minutes rather than months. Pull over, switch off, and get the car recovered rather than driving it on. A converter costs many times what a coil or a plug does.
What causes P0341?
The usual candidates are worn spark plugs, ignition coils, or plug wires; fuel-delivery problems — injectors, pressure, or a lean/rich mixture; vacuum leaks, low compression, or a mechanical fault in that cylinder. The code tells you which test failed, not which of those did it — that is what the checks on this page are for.
Will P0341 clear itself?
Left alone, the lamp goes out on its own once the monitor that failed runs and passes on three consecutive driving cycles. The code stays in history after that, which is how a workshop can still see it. Disconnecting the battery is not a shortcut — it clears the stored codes and every learned fuel-trim value with them, so the car relearns from scratch and the underlying fault simply sets the code again.
Does P0341 mean I need to replace a part?
Do not replace the cam sensor before checking mechanical timing and signal quality; range faults can be caused by timing movement.
How much does it cost to fix P0341?
There is no honest single figure for P0341, and any page that gives you one is guessing. The code names a circuit or a failed monitor, not a part — the same code can be a chafed wire, a connector full of water, or the component itself, and those are three very different bills.
Related OBD-II codes
These nearby ignition / misfire entries can help compare wording and pin down the fault area.